Specification
Product Details
- Amazon Sales Rank: #7277 in Home Improvement
- Brand: Makita
- Model: LXT211
- Number of items: 1
- Dimensions: 5.75" h x
14.75" w x
19.00" l,
Features
- 2-speed 1/2-inch hammer driver-drill (0-400/0-1, 500 RPM) with 4-pole motor delivers 450 inch-pounds of max torque
- Variable-speed impact driver (0-2, 300 RPM) provides 1, 330 inch-pounds of max torque
- Tools feature built-in LED light to illuminate the work area and a rugged tool belt clip
- LXT lithium-ion battery and Energy Star-rated 30-minute charger produce 430 percent total lifetime work with 2.5 times more cycles
- Three-year warranty on tools and one-year warranty on batteries and charger
Product Description
Variable 2-speed 1/2" Hammer Driver-Drill (0-400 & 0-1,500 RPM) with Makita-built 4-pole motor delivers 480 in.lbs. of Max Torque and weighs only 4.0 lbs.
Customer Reviews
Most helpful customer reviews
172 of 176 people found the following review helpful.
By N. Nguyen
The drill is powerful and the hammer action is good for cement and brick fastner drilling. My only gripe is the chuck doesn't bite as hard as my Dewalt. The impact fastner is a beast! Light compact and battery last a really long time. I'm a general contractor and have Dewalt and Milwaukee lithium tools to compare. Makita and Dewalt win this round of lithium tools. Tool quality is excellent. The LED light and belt clip are handy.This tool has gotten fantastic reviews. Ignore the few bad ones. This tool is heavy duty and can handle my punishment as a contractor. We use it every day. It is not made for computer nerds that can build computers yet complain about the reverse switch.It's amazing how ignorant some customers can be."The tool is too powerful and strips screws".....really?? It is a heavy duty tool with over 1330 in.lbs of torque."It is less powerful than my Milwaukee 28Volt".......really? Wanna compare apples to oranges?"It takes two hands to change the hammer to drill action"......again really??? What is your other hand doing and how hard, how often do you change from hammer to drill??
82 of 84 people found the following review helpful.
By Psyclaws
Don't buy the other little compact combo kit (LCT200W) unless you rarely plan to use these tools for more than a few hours at a time and really need to save on weight. Spend a few dollars more, double your battery life, and have the option to add more tools later. Right now, the compact 1.5ah batteries that come with the other kit (LCT200W) only operate three Makita tools (drill, driver, and a light). THIS LXT line with the 3.0 batteries operate 35 tools!In regards to this kit (LXT211), ergo's are important, but most of us are more concerned with torque and battery life. The driver in this combo kit runs at 450 in.lbs, and the impacter hits at 1330 or so. Plenty of torque for whatever you can throw at these tools, and right there with the competition. The impact driver laughs at 3 and 3.5 inch screws! If you need more torque, you should be using a corded rotary hammer drill or ½" pnuematic impact wrench anyway. For my first use of these tools, we built a large 50'X50' deck around a 35' above-ground pool. We tied the 4X4 piers to the 2X8 deck framing with 5/16th lag bolts. I used the drill to bore seventy-five, 5" and 6.5" deep holes through wet, treated pine with an auger bit, and then bolted the nuts with the impact driver. All done on a single charge. I used a Senco Duraspin collated screw fastening system to drive the 2.5" deck screws (3000 of them), but kept my impact driver on my belt for misfeeds and tight spots. It ran all day. I charged it around lunch the first day just to keep it running efficiently, but the charger took less than ten minutes to top it off. The next two days of decking were done on a single charge. I then used the impact driver to set 3" screws for the handrails and stairs. A single lunch-time charge (or battery swap if I wasn't using the drill) kept me going. These Lith-Ion batteries are brutes! The ergos on both tools are terrific, and the weight to power ratio is phenomenal. I will agree that the forward / reverse switch can be inadvertently bumped while in the reverse position. However, it only happened to me when I was in a very awkward angle. For instance, when I was driving the fulcrum screw on a lever board used to suck in a warped deck board. Drilling below plane forces your hand to grip higher on the tool, and can lead to bumping the switch out of the reverse gear. Not really a big deal though, I only mentioned it because others have made a fuss about it. O yea, and fan noise on the charger, really??? It's no louder than a regular PC fan! Lightweight, powerful, and with lithium legs to keep it running all day! Highly recommended!
51 of 58 people found the following review helpful.
By Opti Mystic
So far these have been good tools, but the batteries tend to fail early, after maybe a dozen charges. I checked around on the web and found out there is a design bug in the battery that makes them fail early. Makita knows about it and will quietly replace batteries with under 150 charges on them, regardless of warranty.They seem to fail if left unused for a while, then put on the charger. The symptom is flashing green and red lights on the charger, with a fairly new battery. The reason is a design bug in the control board of the battery. It's always the first cell that fails, gets deep discharged, because its the only one used to supply power to the control board. So it shows a deep discharge, while the other cells are charged. If you try to charge it 3 times with a deep discharged cell, the control board bricks the battery. It will register as bad, even though there is plenty of useful life left.So if this happens, send them to the Makita Service Center for replacement.If Makita won't replace them, you can probably charge them and use them on a clone charger that doesn't read the control board. Clone chargers cost about $60 on the big auction site.Until Makita fixes this, I would not advise buying these tools.
No comments:
Post a Comment